Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - jim

Pages: [1] 2 3 ... 43
1
I paid for a years licence last weekend and it is now on my profile on the Nora website which I think is a pretty fast service.

2
Events / Re: 2024 NORA RACE LICENCES
« on: 21 Mar 24, 05:52 am »
Hi Ian, What are the club charging for one event licences? This year Nora are doing a one event card for £2 to save filling out forms at each event.

3
Events / Re: 1/2 JUNE - CKGB at the NATIONAL KIT CAR SHOW
« on: 07 Mar 24, 02:41 pm »
My Tickets have arrived in the post yesterday and I'm looking forward to this event.

4
Events / Re: IMPORTANT - HELMET REGULATIONS
« on: 07 Mar 24, 02:40 pm »
I have a full face polished helmet that looks awful in my CK but is ECE 22-06. I also have a Bell but I sprayed over it.

5
Events / Re: 1/2 JUNE - CKGB at the NATIONAL KIT CAR SHOW
« on: 02 Mar 24, 08:39 am »
I have paid my entry for this show on the Kitcar website £10+£1 shipping so I guess you change my percentage to 100. (if you want to that is :)

7
Build journals / Re: Something different.
« on: 29 Feb 24, 05:09 pm »
I want to try a different front suspension set up so I'm making a Watts linkage.

8
Tech Forum / Re: Dumb question from a newbie.
« on: 29 Feb 24, 05:00 pm »
Some engines have a 20mm shaft so it's probably one of them.

9
Tech Forum / Re: Louvres/Louvers - DIY Methods
« on: 28 Feb 24, 07:09 pm »
I was looking at drawer cup handles and noticed when put together they could form some very cheap louvres. These are off eBay. They can be riveted to Sheet metal ok.

10
Build journals / Re: 1926 Hudson GP Build
« on: 27 Feb 24, 05:54 am »
Jay, From your pic I would say they are M12 because that looks like a 19mm AF nut. M12 coarse is 1.75mm pitch.

11
Build journals / Re: Something different.
« on: 26 Feb 24, 02:47 pm »
Cool, is there an 8 tooth sprocket on the gearbox?
Thanks Ian and Nick, It's a 10 tooth on the gearbox which has a 1.3:1 ratio. This gives me 7.15:1 ratio from the TAV to the axle. I can't remember the TAV ratios but I should get good acceleration and top end with the motor revving at 5500rpm.

12
Build journals / Re: Something different.
« on: 26 Feb 24, 05:46 am »
Thanks Nick, The power train is a GX clone connected to a FNR gearbox via a TAV which then drives a 55 tooth sprocket on the axle.

13
Build journals / Re: Something different.
« on: 25 Feb 24, 03:22 pm »
So I flipped it back over and started on the body work.

14
Events / Re: 1/2 JUNE - CKGB at the NATIONAL KIT CAR SHOW
« on: 07 Feb 24, 06:12 am »
I am 72% for this. It could be a cracking weekend at that time of year with mucho elbow bending in the bar.

15
Events / Re: 15/16 JUNE - BROOKLANDS "DOUBLE-TWELVE"
« on: 07 Feb 24, 06:08 am »
I'm 19% on this weekend.

Pages: [1] 2 3 ... 43